Veto Pro Pac VPP-TECH-PAC-BLACK Tech Pac Blackout Backpack

Description

The Tech Pac Black is a blacked-out back pack based on our Tech Pac but with front and back removable tool and meter pocket panels which are also exchangeable. You can also purchase a Laptop Panel that can turn the bag into a tool bag/laptop bag, and the Laptop Panel can go in the front or the back. \r\nIncludes Front Tool Panel and Back Tool & Meter Panel, Laptop Panel Sold Separately.\r\n\r\nSpecifications\r\n\r\nHeight (H): 19.5in (49.5cm)\r\nWidth (W): 13in (33cm)\r\nDepth (D): 10in (25cm)\r\nHandle Height (HH): 22in (56cm)\r\nWeight (empty): 12.25lbs (5.5kg)\r\nInternal Volume: 1550in3 (25L)\r\nMax Payload: 50lbs (23kg)\r\n\r\nCapacity\r\n\r\nVertical Tool Pockets: 46 interior and exterior tool pockets of various sizes\r\nUpper Pockets (Front Side) Designed For Extra Tool Capacity\r\n8in Electrical Tape Strap\r\n2 Storage Bays- 4 Storage Platforms\r\nManifold Gauge and Hose Storage Pocket\r\nD-Rings: 4 large and 5 small\r\nOutside Mounted Stainless Steel Tape Clip Holder\r\n\r\nBuild\r\n\r\nLoad Tested: Pulled To Destruction At 830 Pounds(Handle failed); Hook failed at 200 Pounds\r\nWeatherproof Base: 3mm Injection Molded Polypropylene\r\nWeatherproof Body Fabric: 950 and 1250 PVC Impregnated Denier Nylon\r\nAll Blacked-Out Polyester Body Fabric and Construction – Gray Pockets For Better Visibility\r\nQuick Release Metal Hasp: Allows Easy Access to Rear Storage Bay\r\nInternally Stored Aluminum Hook to Hang Bag\r\nOver-Molded Ergonomic Grip\r\nPadded EVA Thermoformed, Ergonomic Back Padding\r\nMetal Shoulder Strap Sliding Buckles\r\nD-Rings: Powder Coated Steel\r\nRivets: Marine Grade Rivets\r\nStitching: Industrial Strength Double Nylon Stitching\r\n\r\nFeatures\r\n\r\nIncludes Front Tool Panel and Back Tool and Meter Panel, Laptop Panel Sold Separately\r\nMetal YKK Locking Zippers\r\nMagnetic Screw Catcher\r\nWarranty: 5 Years (see Veto warranty terms and conditions)\r\n\r\n\r\n\r\nKeep the Zippers Clean and Lubricated\r\n\r\nOver time, dirt and grit will clog the zipper coils preventing them from staying closed. To keep this from happening, clean and lubricate your zippers twice a year (more often if you work on a job site with a high amount of airborne debris). To clean the coils: Scrub them with soapy water; a tooth brush works very well. After scrubbing the coils, blow them out with an air hose to dislodge any other fine grit that didn’t dislodge with the brush. To lubricate the coils: Apply a silicone spray, beeswax or a zipper lubricant.\r\nProtect the Zippers From Sharp Objects and/or Excessive Heat\r\nAny sharp object or heat source is capable of permanently damaging the zippers. Once a zipper coil is cut or singed the zipper will not function and in most cases is not repairable. Most of the cut zipper coils we see are the result of sharp tools stored inside the bag with the sharp side facing up. Make sure to keep the sharp edges of your tools facing down in your bag and away from the zipper coils.\r\nDon’t Overstuff the Bag\r\nOverstuffing your tool bag will very likely cause significant stress on the zippers that is above and beyond what the bag was built for and will eventually cause the zipper(s) to separate. If you have to work hard to close your zipper(s), your tool bag is most likely overstuffed… proceed with caution!